Stormsure Latex Wrist Seal Repair Kit (Bottle Neck Shape)

79,00 zł
+ 73,99 zł wysyłka

Stormsure Latex Wrist Seal Repair Kit (Bottle Neck Shape)

Sugerowana cena detaliczna: 104,00 zł
Cena: 79,00 zł
Oszczędzasz: 25,00 zł (24%)
Sprzedawca: Stormsure
79,00 zł
+ 73,99 zł wysyłka

W magazynie

Akceptujemy następujące metody płatności

Opis

This kit contains all the components that you need to replace the bottleneck shaped wrist seal on a drysuit. Full instructions are on the pack. Make a good quality water tight repair at a fraction of the cost of sending the suit away for repair.   Stormsure Bottleneck Shaped Wrist Seal High Quality Latex made in the UK Size: Medium Top Cone: 44mm diameter Bottom Cone: 89mm diameter Height: 120mm   Stormoprene Adhesive Stormoprene Hypalon Adhesive is a specially formulated 2-part poly-chloroprene based adhesive system for high-performance bonding of Hypalon and other natural and synthetic rubber surfaces that require high strength bonds for use in demanding applications. Formulated for use in the manufacture and repair of RIBs, inflatable boats, liferafts, diving suits, wet suits and other marine and industrial applications that specify resistance to salt water, oil, fuels etc.    Directions: 1. Cut off the damaged seal, leaving the part of the suit where the factory seal is attached to the fabric. The new seal will be glued over the old factory seal edge. 2. Slide the new seal into the factory edge and put an elastic band or bungee around the suit to keep it in place. Slide some silicone/wax paper under the cut off edge to keep glue from sticking to the seal, or you can put wax on the seal. 3. Clean the edge of the suit and the new seal edge with solvent (the side with the stripes is the inside.) Gently sand paper it to roughen the surface. Do not let the seal stick out too far, as the small end of the seal should not be stretched over it. It might cause the new seal to slide out of position. 4. Slide the seal on over the factory rubber area. You can put elastic bands around to keep the new seal from sliding. 5. Roll back the new seal so that the 2cm edge that was over the old suit is now facing up. Apply a thin layer of Stormoprene Contact Adhesive to each side. Wait 5 minutes and apply a second layer of adhesive to each side. Use a spatula or knife to apply the glue. When the glue is touch dry, roll the new latex seal right into place over the rubber part of the old seal. It bonds instantly. Press firmly over the glue area to ensure full adhesion. 6. Take your time.
  • Identyfikator Fruugo: 39549816-81366062
  • EAN: 5060219661084

Informacje o bezpieczeństwie produktu

Prosimy o zapoznanie się z informacjami dotyczącymi bezpieczeństwa produktu określonymi poniżej

Poniższe informacje zostały dostarczone przez niezależnego sprzedawcę zewnętrznego sprzedającego ten produkt.

Ostrzeżenia dotyczące bezpieczeństwa: Causes skin irritation. Causes serious eye irritation. May cause allergy or asthma symptoms or breathing difficulties if inhaled. May cause an allergic skin reaction. May cause respiratory irritation. May cause drowsiness or dizziness. May cause damage to organs through prolonged or repeated exposure.
Składniki: Polychloroprene

Dostawa i zwroty

Stormsure

Adres: Hall Farm, Lode Rd, Cambridge, CB25 9DN, Wielka Brytania
Zarejestrowany numer VAT sprzedawcy: GB599725272
Wszystkie produkty: Odwiedź sklep Stormsure

Prosimy o zapoznanie się z informacjami dotyczącymi zgodności dotyczącymi tego produktu podanymi poniżej.

Poniższe informacje zostały dostarczone przez niezależnego sprzedawcę zewnętrznego sprzedającego ten produkt.

Producent:
Poniższe informacje zawierają dane kontaktowe producenta danego produktu sprzedawanego w serwisie Fruugo.

  • Stormsure
  • Stormsure Europe BV
  • Keisersgracht 520H
  • Amsterdam
  • NL
  • 1017EK
  • contact@stormsure.com
  • 31203694824
  • https://www.stormsure.com

Osoba odpowiedzialna w UE:
Poniższe informacje zawierają dane kontaktowe osoby odpowiedzialnej w UE. Osobą odpowiedzialną jest wyznaczony przedsiębiorca z siedzibą w UE, który jest odpowiedzialny za wypełnianie obowiązków związanych z przestrzeganiem przepisów w odniesieniu do danego produktu sprzedawanego na terenie Unii Europejskiej.

  • Robert Altham
  • Robert Altham
  • Keisersgracht 520H
  • Amserdam
  • NL
  • 1017EK
  • europe@stormsure.com
  • 447836657318
  • https://www.stormsure.com